Part no. (SKU/IDH):
237116
IDH Name:
LOCTITE EA E-30CL DC50MLEN
Legacy IDH:
29329
Structural adhesives
Low viscosity, multi-substrate adhesive for potting applications
This 2-part, low viscosity, industrial-grade adhesive cures at room temperature with minor shrinkage to form an ultra-clear bondline.
Marketing materials
Part no. (SKU/IDH):
237116
IDH Name:
LOCTITE EA E-30CL DC50MLEN
Legacy IDH:
29329
Size Please make your selection 50 ml
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} {{/distributor.anyInStock}}In stock {{#distributor.notInStock}} {{/distributor.notInStock}}Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly.
- Description
- Technical specification
- Question & answer
LOCTITE® EA E-30CL is a low viscosity, industrial grade adhesive. Once mixed, the 2-part epoxy cures at room temperature with minimal shrinkage to form an ultra-clear adhesive bondline with excellent impact resistance. It is resistant to a wide range of chemicals and solvents, and has excellent dimensional stability over a wide temperature range. Perfect for bonding, small potting, staking and laminating applications where optical clarity and excellent structural, mechanical and electrical insulating properties are required. Bonds most materials including glass, optical fibers, ceramics, metals, and many rigid plastics.
-
Excellent impact resistance
-
Low viscosity
-
Chemical and solvent resistant
-
Electrically insulating
- Product category:
- Structural adhesives
Technologies:
-
2K general epoxy
- Applications:
- Bonding fabric; Bonding plastic; Structural bonding
- Color:
- Ultra clear
- Cure type:
- Room temperature (ambient) cure
- FEA (finite element analysis):
- Finite strain; Viscoelastic
- Hardener: Specific gravity, @ 25.0 °C:
- 1.0
- Hardener: Viscosity, Brookfield - RVT, @ 25.0 °C:
- 2250.0 mPa·s (cP)
- Key characteristics:
- Shrinkage: low shrinkage; Temperature: high temperature; Temperature: low temperature; Temperature: medium temperature; Viscosity: low viscosity
- Mix ratio, by volume:
- 2 : 1
- Mix ratio, by weight:
- 100 : 46
- Mixed: Specific gravity, @ 25.0 °C:
- 1.07
- Number of components:
- 2 part
- Recommended for use with:
- Ceramic; Glass; Metal; Plastic
- Resin: Specific gravity, @ 25.0 °C:
- 1.1
- Resin: Viscosity, Brookfield - RVT, @ 25.0 °C:
- 10500.0 mPa·s (cP)
How to use
Use gloves to minimize skin contact. DO NOT use solvents for cleaning hands.
For dual cartridges, insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Remove the cartridge cap and expel a small amount of adhesive to ensure both sides are flowing evenly and freely, then attach the mixing nozzle to dispense the adhesive. For bulk containers, use a volumetric dispensing system to ensure the correct mix ratio and a mixing nozzle to achieve adequate mixing. Allow 24 hours at 22 °C for curing; heating up to 93 °C will accelerate curing, while maximum chemical resistance is achieved after seven days at 22 °C. The mixed product is free flowing and self-leveling, and best potting results are obtained by filling voids from the bottom upward by moving the discharge point accordingly. Keep parts from moving during cure, and position them to retain the product within the potting voids until curing is complete.
Excessive uncured adhesive can be cleaned up with ketone type solvents.
FAQ
Yes, for high strength structural bonds, remove surface contaminants such as paint, oxide films, oils, dust, mold release agents and all other surface contaminants.
LOCTITE® EA E-30CL should be stored in an unopened container in a dry location, as indicated on the product container labeling, with an optimal storage temperature range of 8°C to 21°C. Storage below 8°C or above 28°C can adversely affect product properties. Material removed from the container may become contaminated during use and should not be returned to the original container.
The tensile strength of the cured product is 55 N/mm², measured using the ISO 527-2 test method after curing at 25°C for 5 days.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} {{/distributor.anyInStock}}In stock {{#distributor.notInStock}} {{/distributor.notInStock}}Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly.
Our experts are here to learn more about your needs.
Our support center and experts are ready to help you find solutions for your business needs.