Instant adhesives
Instant component bonding - toughened, low-viscosity adhesive
A rubber toughened, low viscosity, black adhesive ideal for impact applications.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
Size Please make your selection 20 g
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} In stock {{#distributor.notInStock}} Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly. You will receive an email notification when product is back in stock.You will not receive an email notification when product is back in stock.
{{/distributor.isExpanded}}
{{^distributor.isExpanded}}
{{/distributor.isExpanded}}
{{/distributor.isVisible}}
{{/data}}
- Description
- Technical specification
- Ratings & reviews
- Question & answer
LOCTITE® 480 is a black, low viscosity, rubber-toughened instant adhesive designed for close-fitting parts. It has excellent peel, impact and shear strengths and has a fixture time of approximately 90 seconds. It is suitable for use on metals, elastomers and plastics.
-
Toughened, black
-
Low viscosity
-
Excellent peel, impact and sheer strength
-
Easy to use
- Product category:
- Instant adhesives
Technologies:
-
Cyanoacrylate
- Application method, Recommended:
- Dispense system,Manual
- Applications, Recommended:
- Bonding close fitting parts
- Color:
- Black
- Fixture time, Steel:
- 90.0 sec.
- Gap fill:
- 0.18 mm
- Key characteristics, Recommended:
- Toughened
- Operating temperature:
- -40.0 °C - 100.0 °C (-40.0 °F - 212.0 °F)
- Shear strength, Mild Steel (grit blasted):
- 26.0 N/mm² (3800.0 psi)
- Viscosity:
- 200.0 mPa·s (cP)
How to use
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070) to degrease and clean surfaces prior to applying the adhesive.
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
If cure speed is too slow, use activator LOCTITE® SF 7452 or LOCTITE® SF 7455 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
Apply adhesive onto one side/part.
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452. Spray or drop activator onto excess product.
For precise dispensing of small amounts of adhesive, the use of dispensing needles is recommended.
FAQ
There are several methods to toughen CA adhesives, but the most popular ways are using rubber or anhydride toughening agents. The toughening agents are designed to absorb and distribute impact and stress applied to the adhesive bond line resulting in a tougher bond.
This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.
This is a result of stress cracking. Leaving uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, use reinforced grades of plastic, anneal parts, or speed the cure of the CA with accelerator (or light for light curing CA products only)
This is a result of stress cracking. Uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, using reinforced grades of plastic, anneal parts, or speeding the cure of the CA with accelerator (or light for light curing CA products only).
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
Henkel has several products available with varying levels of NSF® approval, amongst others. Please contact the Henkel sales or technical teams with your requirements.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} In stock {{#distributor.notInStock}} Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly. You will receive an email notification when product is back in stock.You will not receive an email notification when product is back in stock.
{{/distributor.isExpanded}}
{{^distributor.isExpanded}}
{{/distributor.isExpanded}}
{{/distributor.isVisible}}
{{/data}}