Wear resistant coatings
Wear prevention - Faster curing, high performance, impact resistant
Designed to protect, rebuild and repair processing equipment subjected to impact due to dropping, rolling, and sliding of large particles. Its faster cure and increased impact resistance outperforms other products in the market.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
2755354
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} In stock {{#distributor.notInStock}} Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly. You will receive an email notification when product is back in stock.You will not receive an email notification when product is back in stock.
{{/distributor.isExpanded}}
{{^distributor.isExpanded}}
{{/distributor.isExpanded}}
{{/distributor.isVisible}}
{{/data}}
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 HARDENER BULK (2596630)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 WIP (2865378)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 A RESIN (2733776)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 RESIN BULK (2596730)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 B HARDENER (2733777)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 B HARDENER (2733777)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 HARDENER BULK (2596630)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 A RESIN (2733776)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 WIP (2865378)en_USIDH: 2755354
-
LOCTITE® PC 9593 Nordbak Wear Prevention Coating , 10 kg Hobbock/PailLOCTITE PC 9593 RESIN BULK (2596730)en_USIDH: 2755354
- Description
- Technical specification
- Ratings & reviews
- Question & answer
LOCTITE® PC 9593 Nordbak Wear Prevention Coating is a faster curing, high performance, impact resistant epoxy resin system designed to protect, rebuild and repair wear areas of processing equipment. Typical applications include dredge pump liners, flumes, troughs, vibrating feeders, chutes & hoppers and other processing equipment that is exposed to both abrasion and impact. It is trowelable, non-sagging and requires no additional tooling.
-
Faster curing, best-in-class resistance to impact and wear
-
Functional cure in only 4 hours
-
Exceptional impact resistance through rubber toughened polymer matrix with alumina bead and silicon carbide
-
Easy to mix and apply; trowelable and non-sagging
-
Coverage: 0.245m @ 6mm thick for a 3KG kit
- Product category:
- Wear resistant coatings
Technologies:
-
Thermosets, 2K general epoxy
- Application method:
- Trowel
- Applications:
- Protective coating
- Color:
- Blue
- Cure type:
- Room temperature (ambient) cure,Two component mix
- Key characteristics:
- Cure speed: fast cure,Impact resistance: high,Wear resistant
- Mix ratio, by volume:
- 2:1
- Mix ratio, by weight:
- 2:1
- Operating temperature:
- < 120.0 °C (< 248.0 °F)
- Physical form:
- Paste
- Recommended for use with:
- Metal
- Shore hardness:
- 85.0
- Work life:
- 15.0 min.
How to use
Remove dirt, oil, grease etc with a suitable high pressure water cleaning system using LOCTITE SF 7840 (LOCTITE® Natural Blue® cleaner/degreaser).
Blast all surfaces to be coated with a sharp edged angular grit to a depth of profile of 75 to 100 microns, and a degree of cleanliness of Near White Metal (SIS SA 2½ /SSPC-SP 10).
After blasting, metal surfaces should be cleaned with a waterless LOCTITE® cleaner, e.g. LOCTITE SF 7365, SF 7063 or SF 7611 and allow the surface to dry before application of the product. Coat the surface before any oxidation or contamination takes place.
To avoid flash rust, repairs should be made as soon as possible. Otherwise, apply a thin coat of LOCTITE SF 7515 to all surfaces and allow to react for 1 minute. After 1 minute, blow off and dry the surface completely with clean and dry compressed air.
Measure 4 parts resin to 1 parts hardener by volume or weight. Transfer measured quantities or entire kit onto a clean and dry mixing surface and mix together with a trowel until uniform in color. If mixing larger quantities, a spiral mixing blade attached to a high torque electric or pneumatic drill can be used. If resin and hardener temperatures are 15°C or below, preheat resin only to about 30°C but not to exceed 40°C.
Apply fully mixed material to the prepared surface. Initially apply the material in a very thin layer to "wet" out the surface and avoid air entrapment. Build up to desired thickness (minimum 6 mm), avoid air entrapment. At 25°C the working time is 30 minutes, and functional cure time is 7 hours. Working and cure time depend on temperature and mass - the higher the temperature and the larger the mass, the faster the cure.
FAQ
A successful application is largely dependent on surface preparation. The application surface must be free from all contamination. Removal of oil, grease, dust, rust and, for most products, moisture, will greatly enhance application success. For more detailed surface preparation techniques, refer to product description sheets.
If a part is cold and the ambient air is warm, cure time will be extended. Both the air and the part should be at room temperature to get the prescribed cure time and strength.
No, epoxy systems have been formulated to contain an exact amount of resin to react with an exact amount of hardener. If excess hardener is added, the resin will remain unreacted and the physical properties of the product will be negatively affected.
The use of solvent is not recommended due to the possibility of trapping the solvent in the cured systems, causing voids or soft spots.
Yes, Polymer Composites are packaged as kits in the exact ratio required. Partial kits, however, can be mixed if measured precisely.
Functional cure time varies with product type and application temperature. Refer to the product description sheets for individual product information.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} In stock {{#distributor.notInStock}} Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly. You will receive an email notification when product is back in stock.You will not receive an email notification when product is back in stock.
{{/distributor.isExpanded}}
{{^distributor.isExpanded}}
{{/distributor.isExpanded}}
{{/distributor.isVisible}}
{{/data}}