Part no. (SKU/IDH):
3124337
IDH Name:
TEROSON® LizardSkin Thermal Control, White, 1 g Hobbock/Pail
Sound dampers
Water-based acrylic thermal insulation coating for automotive applications
This spray-applied thermal insulation coating for automotive use is applied with a pressurized system for fast, clean coverage and minimal waste. Its water-based acrylic formula forms an insulation barrier that reduces heat transfer and improves cabin thermal stability.
Part no. (SKU/IDH):
3124337
IDH Name:
TEROSON® LizardSkin Thermal Control, White, 1 g Hobbock/Pail
Color Please make your selection White
Size Please make your selection 1 g
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} {{/distributor.anyInStock}}In stock {{#distributor.notInStock}} {{/distributor.notInStock}}Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly.
- Description
- Technical specification
- Question & answer
TEROSON® LizardSkin Thermal Control is a water-based acrylic insulation coating available in black and white with a flat finish. It has a moderate wet weight and a high solids content (70.6%) for consistent coverage. The product is suitable for use in applications exposed to elevated temperatures, but should not be applied in environments exceeding 176°C (350°F). Surface preparation requires a dry, clean substrate free of contaminants. Ferrous surfaces should be primed before coating, while clean non-ferrous surfaces can be coated directly. Under typical ambient conditions, the coating dries to the touch quickly and fully cures after a longer curing time.
-
Easy spray application with minimal waste - no cutting, trimming
-
Perfect coverage against corrosion (20-22.5 ft²/gal @ 40 mils WFT) with no seams, joints, or trapped air pockets
-
Adjustable air pressure influences texture and dry time
- Product category:
- Sound dampers
Technologies:
-
Liquid infrastructure coatings
How to use
Ferrous surfaces must be coated with a low gloss automotive primer. Other surfaces should be scuffed with 120 or higher grit sandpaper.
Surface must be free of oil, grease, dust, or any other contaminant. Re-clean with LOCTITE® SF 7840, a weak solvent-based cleaner (Isopropyl Alcohol or Acetone), or a diluted vinegar wash.
Attach mix paddle to variable speed drill. Mix product at a low RPM while moving the stir paddle up and down until product is consistently smooth.
Transfer TEROSON LizardSkin Thermal or Sound Control product into TEROSON LizardSkin SuperPro Kit sprayer cup by holding the bucket 8-10 inches above the cup.
Adjust air compressor to deliver 50-70 PSI at the gun.
Adjust spray tip by screwing in the nozzle until it bottoms out, then bring it back out 2 complete turns (720°). Tighten the lock collar.
Apply product in a crosshatch pattern (vertical, then horizontal passes) with slight overlaps.
Press Wet Mil Gauge (included in TEROSON LizardSkin SuperPro Kit) into wet coating. Application thickness should be 20mil (0.5mm). Do not exceed 24mil (0.6mm) thickness.
Test coat by pressing thumb against the coating with light to medium pressure and twist 90°; if coating does not stick to your thumb, repeat steps 7 & 8.
Allow the product dry for 36-48 hours at 23°C (73°F) before reassembly or top coating. Do not force dry with heat.
FAQ
It is designed specifically for automotive insulation applications.
Applications should not exceed 350°F (176°C).
The recommended per coat application is 20 mils (0.5mm) WFT.
Ferrous surfaces should be primed prior to application. Non-ferrous surfaces can be coated directly if clean and free of contaminants.
The product should be stored between 60°F and 90°F and must not be allowed to freeze.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
{{#distributor.onShelf}} {{#distributor.withSpecialPrice}} {{distributor.prices.specialWithSymbol}}
{{distributor.prices.regularWithSymbol}}
{{#distributor.withoutSpecialPrice}} {{distributor.prices.regularWithSymbol}}
{{#distributor.anyInStock}} {{/distributor.anyInStock}}In stock {{#distributor.notInStock}} {{/distributor.notInStock}}Out of stock {{#distributor.notOnShelf}} {{^distributor.notInStock}} {{#distributor.onShelf}} All available stock is already in cartYou have reached the maximum order quantity availableFor industrial use only. Not intended for consumer sale or use.
Large volume or special order?
{{#distributor.notOnShelf}} {{/distributor.notInStock}}{{#distributor.notInStock}} {{#distributor.onShelf}} {{#distributor.notInStock}} {{/distributor.onShelf}}There was a problem with your request. Please try again or contact us directly.
Our experts are here to learn more about your needs.
Our support center and experts are ready to help you find solutions for your business needs.