Skip to Content
Henkel Adhesive Technologies
Recent searches

      Henkel Adhesive Technologies

      Instant adhesives

      LOCTITE® 4014

      Instant component bonding - very low viscosity, medical grade, fast-fixturing

      This fast-fixturing, very low viscosity instant adhesive is suitable for the assembly of disposable medical devices.

      Technical (1)

      RoHS (1)

      Regulatory (1)

      Part no. (SKU/IDH):
      202152

      IDH Name:
      LOCTITE® 4014, 20 g Bottle
      Part no. (SKU/IDH) 202152
      LOCTITE® 4014, 20 g Bottle

      Size Please make your selection 20 g

      All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.

      Information

      LOCTITE® 4014 is a very low viscosity instant adhesive (medical device grade) designed for the assembly of a wide range of materials. It is ideally suited for tight-fitting parts and provides fast room-temperature fixturing. Using primer LOCTITE® SF 7701, the assembly of difficult-to-bond (PP, PE, PTFE) materials is possible. LOCTITE 4014 is tested to Henkel's ISO 10993 protocols for use in disposable medical devices.
      • Medical grade instant adhesive
      • Assembles difficult-to-bond plastics when LOCTITE® SF 7701 primer used
      • Very low viscosity for close-fitting parts
      • ISO-10993 biocompatible
      • Product category:
      • Instant adhesives

      Technologies:

      • Cyanoacrylate
      • Color:
      • Ultra clear

       

      • Fixture time:
      • 10.0 sec. - 30.0 sec.

       

      • Gap fill:
      • 0.15 mm

       

         

           

             

               

                 

                   

                     

                       

                         

                           

                             

                               

                                 

                                   

                                     

                                       

                                         

                                           

                                             

                                               

                                                 

                                                  How to use

                                                    It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070) to degrease and clean surfaces prior to applying the adhesive.

                                                    To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 7701 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.

                                                    If cure speed is too slow, use activator LOCTITE® SF 713 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.

                                                    Apply adhesive onto one side/part.

                                                    Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.Hint: if necessary, excess product can be cured by activator LOCTITE® SF 713. Spray or drop activator onto excess product.

                                                  FAQ

                                                    LOCTITE® Medical Device Grade Adhesives have been tested to Henkel's ISO-10993 biocompatibility protocols, making them candidates for use in disposable medical devices. They are not intended for implants and (invasive) prostheses.

                                                    ISO-10993 Biocompatibility Certificates of Test for LOCTITE® Medical Device Adhesives are available via our Medical Website or by contacting Henkel directly.

                                                    Yes, CA’s should be stored in the refrigerator prior to opening, but DO NOT refrigerate them once they have already been opened. After opening, CA's should be used within 30 days for best performance.

                                                    All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.

                                                    This is a result of stress cracking. Uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, use reinforced grades of plastic, anneal parts, or speed the cure of the CA with accelerator (or light for light curing CA products only).

                                                    This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.

                                                  Recently viewed products

                                                  Request a consultation

                                                  Unplanned downtime or lower plant productivity can prevent you from achieving the manufacturing excellence that you are looking for. Consult with our experts to find ways to make your machine more reliable and reduce unplanned downtime to save costs.
                                                  Contact an expert

                                                  Henkel Adhesive Technologies
                                                  Company
                                                  About us
                                                  Locations
                                                  Careers
                                                  News
                                                  Current Customer eShop
                                                  Sustainability
                                                  Help
                                                  FAQs
                                                  Find a TDS
                                                  Find a SDS
                                                  Find a distributor
                                                  Contact us
                                                  Resource center
                                                  Product search
                                                  Technical Library
                                                  Case studies
                                                  White papers
                                                  Webinars
                                                  Brochures
                                                  Social media
                                                  ⓒ 2024 Henkel Corporation. ALL RIGHTS RESERVED
                                                  You are on a United States website