Part no. (SKU/IDH):
142442
IDH Name:
LOCTITE® 603, 50 ml Bottle
Retaining compounds
Powerful, low-viscosity retaining compound for close-fitting cylindrical parts
A 1-part retaining compound designed for bonding cylindrical fitting parts, such as bearings, bushings and shafts.
Part no. (SKU/IDH):
142442
IDH Name:
LOCTITE® 603, 50 ml Bottle
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
- {{^distributor.unique}} {{/distributor.unique}} {{/distributor.isExpanded}} {{^distributor.isExpanded}} {{/distributor.isExpanded}} {{/distributor.isVisible}} {{/data}}
- Description
- Technical specification
The low viscosity of LOCTITE® 603 makes it ideal for augmenting press/interference fits, or slip-fitted assemblies with small clearances. The high-strength adhesive reliably prevents loosening from shock and vibration on cylindrical parts, such as roller bearings or oil-impregnated bushings mounted in housings, while it also prevents corrosion between the metal parts.
-
High-strength retaining compound for cylindrical assemblies
-
Perfect for bearings, bushings, and shafts
- Product category:
- Retaining compounds
Technologies:
-
Acrylates, anaerobic cure
- Agency approvals / certificates / specifications:
- NSF; WRAS
- Colour:
- Green
- Fixture time:
- 10.0 min.
- Gap fill:
- 0.15 mm
- Key characteristics:
- Oil tolerant; Viscosity: low viscosity
- Operating temperature:
- -55.0 °C - 150.0 °C (-65.0 °F - 300.0 °F)
- Recommended for use with:
- Metal: steel
- Shear strength, Steel:
- 26.0 N/mm² (3770.0 psi)
- Viscosity:
- 125.0 mPa·s (cP)
How to use
Use LOCTITE® 7200 for easier removal of residues in case of old retaining adhesive. It is recommended to use LOCTITE® 7063 to degrease and clean surfaces prior to applying the adhesive. For gaps larger than 0.5mm or worn out shafts, bearing seats or keyways, use LOCTITE® metal-filled compounds.
If cure speed is too slow due to passive metals or low temperature (below 5°C), use activator LOCTITE® 7240 or LOCTITE® 7649 (see cure speed vs activator graph in the TDS).
Apply adhesive around the leading edge of the male component and the inside of the female component and use a rotating motion during assembly to ensure good coverage.
Apply adhesive thoroughly to both bond surfaces and assemble at high press on rates.
Apply the adhesive onto the shaft; heat the collar to create enough clearance for free assembly.
For manual assembly of adhesive, the use of a peristaltic hand pump is recommended to ensure a consistent application volume. For semi-automatic or fully-automated dispensing options, contact our technical service team for advice.
Apply localised heat to approximately 250°C; disassemble while hot. For corroded or seized parts, use LOCTITE® LB 8040 Freeze and Release.
FAQ
Fixture time is the time taken for the adhesive to provide initial handling strength – quoted as 0.1N/mm². Once fixtured, the assembly can usually be handled/moved on for further processing.
Cure time is the time taken for the adhesive to reach its final mechanical properties.
The optimum fit for thinner / low viscosity products like LOCTITE® 603 is 0.025 mm to 0.08 mm. For thicker / high viscosity products like LOCTITE® 638, it is 0.05 mm to 0.1 mm. Optimum clearance (D-d) is application and substrate specific. Please contact Henkel's technical team for details and guidance.
The standard continuous operating temperature range for LOCTITE® anaerobic adhesives is -55˚C to +150˚C.
Depending on the specific application requirements, high-performance grades are also available offering increased temperature resistance. Please consult with the Henkel technical team for availability and grade selection.
Product selection is specific to each application. As a rule of thumb, thinner / low viscosity products are used for tighter fitting parts with low diametrical clearance; thicker / high viscosity products are used were gap-filling capability is needed. Bonded heat shrink fit assemblies will utilise a low viscosity product with high thermal resistance, e.g. LOCTITE® 648.
For slip fitted assemblies, apply to the leading edge of the male part and female parts. Assemble with a twisting motion. For press fitted assemblies, apply adhesive generously to both bond surfaces and assemble with a high press on rate. For shrink fitted assemblies, apply adhesive to the shaft, and heat the collar to create sufficient clearance for free assembly.
Yes, all LOCTITE® anaerobic adhesives will lock and seal components and assemblies, preventing failure from vibrational loosening and corrosion.
There are several factors which will affect the cure speed or fixture time of Henkel anaerobic adhesives - most noatably the substrate material, the bond gap and the application temperature. Anaerobic adhesives cure by the chemical reaction with active metal ions (specifically Iron or Copper) and the exclusion of air within small gaps to cure. If the substrates are passive (low iron or copper content), or the ambient temperature is low, the cure reaction may be slow. In these circumstances an activator can be applied to the substrate prior to bonding to speed up the reaction. Alternatively, the components can be heated to speed up the reaction and reduce the fixture and cure time. Please see more details on the relevant technical data sheet.
If the parts cannot be separated using mechanical methods alone, Henkel recommends applying localised heat to the components for several minutes before applying force. Long-term exposure to temperatures in excess of 260°C will start to degrade the adhesive and can aid disassembly.
Yes, Henkel anaerobic adhesives become highly resistant thermoset polymers once cured, making them suitable for a vast number of applications. Consult the online product resources or contact our technical teams for further information.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
Henkel has several products available with varying levels of NSF® and WRAS® approval, amongst others. Please contact the Henkel sales or technical teams with your requirements.
Some LOCTITE® anaerobic adhesives will fluoresce under UV light, allowing for visual inspection and confirmation that the assemblies have been bonded successfully.
Some LOCTITE® anaerobic adhesives have been formulated to be tolerant to light oil contamination of parts, allowing for immediate application and eliminating additional cleaning processes in some applications. Contamination levels may vary. Excessive contamination and using an adhesive which is not oil tolerant will reduce the strength and overall success of a bonded assembly. Please speak to Henkel's technical team for information and guidance.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
- {{^distributor.unique}} {{/distributor.unique}} {{/distributor.isExpanded}} {{^distributor.isExpanded}} {{/distributor.isExpanded}} {{/distributor.isVisible}} {{/data}}
