Instant adhesives
Instant component bonding - general purpose
A general purpose, low-viscosity instant adhesive for fast fixturing and bonding of a wide range of materials.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
- Description
- Technical specification
LOCTITE® 495 is a transparent, colorless, low viscosity, general purpose instant adhesive offering fast fixturing. It is able to bond a wide range of materials, including plastics, rubbers and metals. It can also bond polyolefins when used in combination with LOCTITE® SF 770 primer.
-
General purpose colorless and transparent bonding
-
Low viscosity for thin bond lines
-
Ideal for quick repairs
-
Reduced hazardous ingredients for improved occupational safety
- Product category:
- Instant adhesives
Technologies:
-
Cyanoacrylate
- Application method:
- Dispense system,Manual
- Applications:
- Bonding plastic,Bonding rubber,Repairing
- Color:
- Clear
- Cure type:
- Moisture cure
- Fixture time, Steel:
- 5.0 sec.
- Gap fill:
- 0.12 mm
- Key characteristics:
- General purpose,Viscosity: low viscosity,fixture: very fast fixture
- Operating temperature:
- -40.0 °C - 120.0 °C (-40.0 °F - 250.0 °F)
- Physical form:
- Liquid
- Recommended for use with:
- Elastomer,Metal,Plastic,Porous surface
- Shear strength, Mild Steel (grit blasted):
- 14.2 N/mm² (2060.0 psi)
- Viscosity:
- 40.0 mPa·s (cP)
How to use
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7063 or SF 7070) to degrease and clean surfaces prior to applying the adhesive.
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
If cure speed is too slow, use appropriate activator LOCTITE® SF 7452 or LOCTITE® SF 7455 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
Apply adhesive onto one side/part.
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.
Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452 or LOCTITE® SF 7455. Spray or drop activator onto excess product.
For precise dispensing of small amounts of adhesive, the use of dispensing needles is recommended.
FAQ
Although HQ is not part of the product formula for LOCTITE® 495, trace amounts are possible due to shared manufacturing processes and/or select raw material impurities. Hence, Henkel has taken the additional step of introducing a low specification level (< 50 PPM for HQ) and each batch is now checked for this after manufacture.
All adhesives are compatible with metal substrates although bond strength and durability will vary depending on the technology selected. Anaerobic adhesives may cause stress-cracking in some sensitive polymers and therefore should generally be avoided on plastic parts. Consult Henkel technical teams for further advice as needed.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
This is a result of stress cracking. Leaving uncured liquid CA remaining on some plastic substrates (such as polycarbonate, acrylic, and polysulfone) in a stressed condition, may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, using reinforced grades of plastic, anneal parts, or speed cure the adhesive with accelerator or light (for light cure products only).
This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.
Yes, instant adhesives should be stored in the refrigerator prior to opening, but DO NOT refrigerate them once they have already been opened. After opening, the product should be used within 30 days for best performance.
