Instant adhesives
Instant component bonding - your go-to fast-fixturing gel
A surface-insensitive, fast-fixturing gel instant adhesive ideal for pourous and acidic materials.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
- Description
- Technical specification
LOCTITE® 454 is a gel viscosity instant adhesive designed for large bond gaps and vertical applications. It provides for the rapid bonding of a wide range of materials including metals, elastomers and plastics, including difficult-to-bond plastics (PP, PE, PTFE) with the aid of a primer such as LOCTITE SF 770. LOCTITE 454 is also suited for bonding porous materials such as wood, paper, leather and fabric. It is also ideal for all quick repair jobs.
-
Clear, universal instant adhesive gel
-
Operating temperatures from -54°C to 121°C (-65°F to 250°F)
-
Ideal for overhead application and vertical faces
-
Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics
-
Reduced hazardous ingredients for improved occupational safety
- Product category:
- Instant adhesives
Technologies:
-
Cyanoacrylate
- Application method:
- Dispense system,Manual
- Applications:
- Overhead/vertical application,Repairing
- Color:
- Clear
- Cure type:
- Moisture cure
- Fixture time, Steel:
- 45.0 sec.
- Gap fill:
- 0.25 mm
- Key characteristics:
- Fixture: fast fixture,General purpose,Tensile strength: high tensile strength,Viscosity: high viscosity
- Operating temperature:
- -54.0 °C - 121.0 °C (-65.0 °F - 250.0 °F)
- Physical form:
- Gel
- Recommended for use with:
- Elastomer,Metal,Plastic,Porous surface
- Shear strength, Mild Steel (grit blasted):
- 20.9 N/mm² (3030.0 psi)
How to use
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7063 or SF 7070) to degrease and clean surfaces prior to applying the adhesive.
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
If cure speed is too slow, use appropriate activator LOCTITE® SF 7452 or LOCTITE® SF 7455 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
Apply adhesive onto one side/part.
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.
Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452 or LOCTITE® SF 7455. Spray or drop activator onto excess product.
For precise dispensing of small amounts of adhesive, the use of dispensing needles is recommended.
FAQ
Although HQ is not part of the product formula for LOCTITE® 454, trace amounts are possible due to shared manufacturing processes and/or select raw material impurities. Hence, Henkel has taken the additional step of introducing a low specification level (< 50 PPM for HQ) and each batch is now checked for this after manufacture.
This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.
Yes, instant adhesives should be stored in the refrigerator prior to opening, but DO NOT refrigerate them once they have already been opened. After opening, the product should be used within 30 days for best performance.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
This is a result of stress cracking. Leaving uncured liquid CA remaining on some plastic substrates (such as polycarbonate, acrylic, and polysulfone) in a stressed condition, may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, using reinforced grades of plastic, anneal parts, or speed cure the adhesive with accelerator or light (for light cure products only).
Henkel has several products available with varying levels of NSF® and WRAS® approval, amongst others. Please contact the Henkel sales or technical teams with your requirements.
