Part no. (SKU/IDH):
201507
IDH Name:
LOCTITE® 382, 500 g Bottle
Instant adhesives
High-viscosity gel for wire tacking
A 1-part, high-viscosity instant adhesive, well suited for electronics applications, e.g. wire tacking to coil forms, edge guides, and stiffeners to circuit boards.
Part no. (SKU/IDH):
201507
IDH Name:
LOCTITE® 382, 500 g Bottle
Size Please make your selection 500 g
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
- {{^distributor.unique}} {{/distributor.unique}} {{/distributor.isExpanded}} {{^distributor.isExpanded}} {{/distributor.isExpanded}} {{/distributor.isVisible}} {{/data}}
- Description
- Technical specification
LOCTITE® 382 is a high-viscosity instant adhesive formulated for electronic applications, and has a fixture time of 20-40 seconds. It is ideal for wire tacking applications when used together with a LOCTITE accelerator. It is also suitable for rubbers, metals and plastics, including polyolefin and other difficult-to-bond plastics when used with LOCTITE® SF 770 primer – making it also a general-purpose product.
-
For tacking wire to coil forms; tamper-proofing components; mounting standoffs, edge guides and stiffeners to circuit boards
-
Bonds metals, elastomers, plastics, including difficult-to-bond plastics when LOCTITE SF 770 used
-
General-purpose
-
High viscosity
- Product category:
- Instant adhesives
Technologies:
-
Cyanoacrylate
- Colour:
- Ultra clear
- Fixture time:
- 20.0 sec. - 40.0 sec.
- Gap fill:
- 0.15 mm
How to use
It is recommended to use LOCTITE® SF 7063/7064 to clean and degrease surfaces prior to bonding. Ensure the cleaning solvent is compatible with the materials to be bonded and has dried prior to adhesive application.
Apply LOCTITE®SF 7455 or LOCTITE® SF 7458 activator to the bond area, by spray, brush or dipping. Allow the activator time to evaporate, under good ventilation, until the surfaces are completely dry (approx. 15 to 30 seconds).
Apply LOCTITE® 382 to the bond area and assemble the parts. Where possible, move surfaces in relation to each other for a few seconds to distribute the adhesive and for maximum activation. Secure the assembly and await fixturing before any further handling. If necessary excess product can be cured by activator LOCTITE® SF 7455 or LOCTITE® SF 7458.
FAQ
This is a result of stress cracking. Uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, use reinforced grades of plastic, anneal parts, or speed the cure of the CA with accelerator (or light for light curing CA products only).
This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.
Yes, CA’s should be stored in the refrigerator prior to opening, but DO NOT refrigerate them once they have already been opened. After opening, CA's should be used within 30 days for best performance.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
Henkel has several products available with varying levels of NSF® approval, amongst others. Please contact the Henkel sales or technical teams with your requirements.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
- {{^distributor.unique}} {{/distributor.unique}} {{/distributor.isExpanded}} {{^distributor.isExpanded}} {{/distributor.isExpanded}} {{/distributor.isVisible}} {{/data}}
