Threadlockers
Red, high strength, primerless threadlocker stick
Easy-to-apply, semi-solid, high-strength stick for locking and sealing threaded assemblies permanently - ideal for vertical and overhead applications. Removable with heat.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
- Description
- Technical specification
LOCTITE® 268 is a red, high-strength threadlocker for permanently locking and sealing bolts, nuts and studs to prevent loosening due to vibration. The non-drip stick format makes it ideal for vertical and overhead applications. It works on all metals without primer, including passive substrates such as stainless steel, aluminum and plated surfaces. Suitable for use on most oil-coated, 'as-received' fasteners without cleaning.
-
Convenient, non-drip, stick format
-
High torque strength
-
Prevents fastener loosening on vibrating assemblies, e.g., pumps, gear boxes, presses
-
Works on all metals without primer, including passive substrates
-
Suitable for use on most oil-coated, 'as-received' fasteners without cleaning
-
Can be disassembled by heating to 300°C (572°F)
- Product category:
- Threadlockers
Technologies:
-
Acrylates, anaerobic cure
- Application temperature:
- -65.0 °F - 300.0 °F (-55.0 °C - 150.0 °C)
- Breakaway torque, Breakloose torque:
- 10.0 N·m (90.0 in./lb.)
- Color:
- Red
- Fixture time:
- 5.0 min.
- Physical form:
- Semi-solid stick
- Recommended for use with:
- Metal: steel,Metal: steel - stainless steel
How to use
LOCTITE 268 is suitable for use on most “as-received” fasteners with light coatings of corrosion prevention oils without cleaning. However, for heavily oiled or contaminated fasteners, it is recommended to use LOCTITE® SF 7070 to degrease and clean surfaces prior to applying LOCTITE 268 threadlocker.
If cure speed is too slow due to passive metals (stainless steel, aluminum and plated metals) or low temperature (below 5°C), use LOCTITE® SF 7649 activator. Allow to dry.
Apply a 360 degree band of threadlocker to the male fastener at the area of engagement and completely fill the thread roots - generally the width of 2-3 threads. Assemble nut and tighten to proper torque.
Apply threadlocker to entire diameter of thread engagement area on male fastener, install fastener into blind hole, and tighten to proper torque.
Assemble and tighten to proper torque requirement. If several bolts are being assembled, torque them down to the correct value within the fixture time window.
Disassemble with standard hand tools. If not possible, apply localized heat to approximately 500°F/260°C and disassemble while hot.
FAQ
Prevent vibration loosening, prevent leaks, protect threaded components from corrosion and increase the reliability of mechanical fasteners by using a LOCTITE® anaerobic threadlocking adhesive.
The standard continuous operating temperature range for LOCTITE® anaerobic adhesives is -65°F to +300°F (-55˚C to +150˚C).Depending on the specific application requirements, high-performance grades are also available offering increased temperature resistance. Please consult with the Henkel technical team for availability and grade selection.
Yes, LOCTITE® threadlockers become highly resistant thermoset polymers once cured, making them suitable for a vast number of applications. Consult Henkel's online product Technical Data Sheets (TDS) and other product resources, or contact our technical teams for further information.
Yes, these products are all anaerobic adhesives that will function in a similar way. Variations in the adhesive characteristics (viscosity, gap-fill, strength, etc.) will make them better suited to certain applications. Consult the product technical data sheets and/or Henkel representatives for further information.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
