Instant adhesives
Instant component bonding - Low viscosity, flexible adhesive for medical devices
This flexible cyanoacrylate adhesive offers near instant bonding while retaining flexibility once cured and fixed. It is ideal for flexing and bending applications in disposable medical device assembly.
All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.
524540
- Description
- Technical specification
LOCTITE® 4851 is a flexible, low viscosity instant adhesive specifically formulated to provide flexible bondlines. It develops fixture strength in approximately 10 seconds and is suited for bonding metals, elastomers and plastics, including difficult-to-bond plastics (PP, PE, PTFE) when used with a primer such as LOCTITE® SF 7701. LOCTITE 4851 is tested to Henkel's ISO 10993 protocols for use in disposable medical devices.
-
Specifically formulated to provide flexible bondlines
-
Assembles difficult-to-bond plastics when LOCTITE® SF 7701 primer used
-
Low viscosity
-
Tested to Henkel's ISO-10993 biocompatibility protocols
-
Particularly suited to bonding porous or absorbent materials such as paper, leather and fabrics
Agency approvals / certificates / specifications:
ISO 10993
Cure type:
Moisture Cure
Key characteristics:
Viscosity: Medium Viscosity
Number of components:
1 Part
Physical form:
Liquid
Recommended for use with:
Acrylonitrile Butadiene Styrene (ABS),Metal: Steel,Polycarbonate
Specific gravity, @ 25.0 °C:
1.1
How to use
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070™) to degrease and clean surfaces prior to applying the adhesive.
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 7701™ to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
If cure speed is too slow, use activator LOCTITE® SF 713™ (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
Apply adhesive onto one side/part.
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.Hint: if necessary, excess product can be cured by activator LOCTITE® SF 713™. Spray or drop activator onto excess product.
FAQ
LOCTITE® Medical Device Grade Adhesives have been tested to Henkel's ISO-10993 biocompatibility protocols, making them candidates for use in disposable medical devices. They are not intended for implants and (invasive) prostheses.
ISO-10993 Biocompatibility Certificates of Test for LOCTITE® Medical Device Adhesives are available via our Medical Website or by contacting Henkel directly.
Yes, CA’s should be stored in the refrigerator prior to opening, but DO NOT refrigerate them once they have already been opened. After opening, CA's should be used within 30 days for best performance.
All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.
This is a result of stress cracking. Uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, use reinforced grades of plastic, anneal parts, or speed the cure of the CA with accelerator (or light for light curing CA products only).
This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.
-
{{#data}}
{{#distributor.isVisible}}
{{#distributor.isExpanded}}
-
{{^distributor.unique}}
{{/distributor.unique}}
